|
Author
|
Topic: Lap Steel String Selection
|
Brad Smith
New Member From: Westboro, MA, USA
|
posted 28 December 1999 09:34 AM
profile send email edit
Flat or Round? I'm new to lap steel playing. Wouldn't it be more authentic to use flat wound strings to replicate a 40's,50's and 60's sound? Wouldn't flat wounds give off less bar noise on slides? Excuse my ignorance, I've only tried round wound so far.
|
Tele
Member From: Andy W. - Wolfenbuettel, Germany
|
posted 28 December 1999 10:33 AM
profile send email edit
Hiactually I've never tried Flatwounds on my steels but I'm experimenting a lot with Flatwounds on my vintage standard guitars. If you would choose them be sure to get pure nickel flatwounds because only the nickel strings sound "vintage". They work best with single coils, not so good with humbuckers and the output is lower. Unfortunately only a few companies offer them, the best nickel flatwounds are Pyramids( Germany) ------------------
Fender Custom Triple 8
Emmons S-10
1954 Super Amp
1958 Telecaster
|
Bob Kagy
Member From: Lafayette, CO USA
|
posted 28 December 1999 11:43 AM
profile send email edit
It's my opinion of course, but I'm of the fairly strong feeling that the flats or semi-flats don't have the resonance and sustain that round wounds have.So the trade-off is that with rounds you get more bar noise, but with the flats you get less tone. Again, only my opinion, but try them both and see what you think. Regards, Bob
|
Ray Montee
Member From: Portland, OR, USA
|
posted 30 December 1999 10:06 PM
profile send email edit
Jerry Byrd for YEARS....used Spanish Guitar strings and acquired a fantabulous tone no matter what tune he played. Admiring his playing for so many years, as I have, I too have used BLACK DIAMOND spanish guitar strings; for the 1st, 2nd and 3rd strings, I use a SECOND STRING. I use a spanish guitar 3rd string(plain/not wound)for my 4th string. JB then used flat wounds for his 5th,6th and/or 7th strings. If it's good enough for JB....it's good enough for me. I'm not a pro player either. I was once told by a reasonably experienced professional musician that there is only about 4 string manufacturers in the USA anyway, so I wonder..........? I've heard at least three dozen string names during my first year visiting the forum |
mikey
Member From: Hawaii, Big Island
|
posted 30 December 1999 10:39 PM
profile send email edit
I've always used standard electric guitar strings, usually Ernie Balls....you can get any gauge you want, anywhere in the world....
Mike |
Chris DeBarge
Member From: Boston, Mass
|
posted 31 December 1999 07:04 AM
profile send email edit
I've looked the world(wide web) over for flat wound singles in order to make sets for my steels-NOBODY seems to sell the singles. My next step is to approach the manufacturers. I'm leaning towards GHS, reasons:
D'addario- their "chromes" flatwounds sound and feel awful on a regular guitar.
Thomastik- awesome flatwounds for guitar, but too expensive
Pyramid- same
I look forward to some advice/opinions on this subject.On the same subject, has anyone tried the SIT semi-flats that are already prepackaged in popular non-pedal sets? I'm intrigued and was hoping someone has an opinion on these as well. If nothing works out soon, you may soon be seeing Chris DeBarge brand flatwound sets at a steel guitar store near you! |
John Tipka
Member From: Reynoldsburg,OH
|
posted 31 December 1999 12:18 PM
profile send email edit
Chris,
I use GHS flatwounds on all of my guitars. I buy them from Scotty's Music. You were just looking in the wrong places on the Internet. Flats-GHSF22 through GHSF60. The compound wounds are GHSC64 through GHSC74. Semiflats are GHSN18 through GHSN60. Last two digits are the string gauge.
http://www.iwc.com/scottys-music/ghssingles.htm Regards, John
http://www.iwaynet.net/~steelgtr |
The Steel Guitar Forum
