Steel Guitar Strings
Strings & instruction for lap steel, Hawaiian & pedal steel guitars
http://SteelGuitarShopper.com
Ray Price Shuffles
Classic country shuffle styles for Band-in-a-Box, by BIAB guru Jim Baron.
http://steelguitarmusic.com

This Forum is CLOSED.
Go to bb.steelguitarforum.com to read and post new messages.


  The Steel Guitar Forum
  Pedal Steel
  Ringing strings

Post New Topic  
your profile | join | preferences | help | search

next newest topic | next oldest topic
Author Topic:   Ringing strings
Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 25 October 2005 06:57 AM     profile     
Got a great tip from a friend at the Rhode Island Steel Guitar show yesterday. I would like to pass it on to you folks out there in Steel Guitarland.Go down to Radio Shack and buy some Heat-shrink tubing'cost was 2.59. The pack I bought had different sizes in there;you want to use the smallest tube.The tubing goes over the wound part of the string at the ball. You do not want the tubing past that pount! Take care when measuring lenght needed.Worked for me. Thanks again Sam for the tip.Ringing is gone

Ron C.

Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 25 October 2005 07:01 AM     profile     
Sorry re. the mispelled words above. I do not type very often; If you have that problem, try the above!Ron C.

Fred Shannon
Member

From: Rocking "S" Ranch, Comancheria, Texas

posted 25 October 2005 10:29 AM     profile     
Well Duh!! Ron that's one this old dinosaur has never heard of. Wonder if you or someone can explain the rationale behind this?

I'm assuming the heat shrink "does not" interfere with the contact the string makes with the changer finger. Just don't 'unnerstan'.
Phred

richard burton
Member

From: Britain

posted 25 October 2005 11:49 AM     profile     
I've used a variant of this idea on problematic 'whining' plain strings.
I put a very thin piece of plastic under the string, where it passes over the changer
finger.
This cuts out the whining tail-end of the note.
Look at the 4th string in this pic:

[This message was edited by richard burton on 29 October 2005 at 03:22 AM.]

Ron Sodos
Member

From: Albuquerque, New Mexico, USA

posted 27 October 2005 08:36 AM     profile     
Sounds to me like you are cutting off your tone. The whole idea is to have steel string to steel roller. If you put plastic between the string and the roller you lose all your tone......Don't get it at all????

[This message was edited by Ron Sodos on 27 October 2005 at 08:36 AM.]

richard burton
Member

From: Britain

posted 27 October 2005 11:36 AM     profile     
Here's the tone I get.
Tone is subjective, I like this tone, others may find it objectional. http://www.freefilehosting.net/?id=r9D1kKjQ
http://www.freefilehosting.net/?id=rd32kazQ

[This message was edited by richard burton on 27 October 2005 at 11:39 AM.]

Carlos Polidura
Member

From: Brooklyn, New York, USA

posted 27 October 2005 12:18 PM     profile     
very nice richard...
carlos
Rick Nicklas
Member

From: Pleasant Ridge, Mo

posted 28 October 2005 06:18 AM     profile     
Hey guys... To most, this is a post they would pass by. But to me it is one of the most important I have read. I have buffed down the finger, got new pickups etc. etc... and have always had the "E" string whining. I hate it because I always get a great tone in the treble range that opens my bass strings up also but I have to always back off because of the whining string. I hope one of these methods works for me so I can adjust my tone back to the clarity that is so great. This has gone on for years and probably the most irritating delima for me.
Ronald... do I actually apply heat to the shrink rap after putting it on? If I follow your directions then the wrap will not go over the top of the finger and the string will still be on the steel part of the finger on top.... right?
Richard... what type of plastic are you using there. Can I get something at a hardware store. Looks like your's is molded over the finger.
I'm going to try both options until the problem is corrected. I really appreciate your posting this message. I almost started crying when I read it because my hopes went sky high..... again, thanks a million!!!


------------------
Rick
Kline U-12, Session 500, Goodrich L-10k


[This message was edited by Rick Nicklas on 28 October 2005 at 06:19 AM.]

[This message was edited by Rick Nicklas on 28 October 2005 at 06:23 AM.]

Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 28 October 2005 07:01 AM     profile     
Hi Rick,

I think there exists some confusion as to the material I am talking about! This is not wrap. These tubes are like plastic straws of various sizes.The best I can suggest is for you to go down to your local Radio Shack ,and ask for " Heat Shink Tubing" .There are different colored tubes in the package, the cost is 2.59 .Then follow instructions in my above post

Good luck, Ron C.

Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 28 October 2005 07:12 AM     profile     
Hi Rick,
I should have mentioned, You do not apply any heat to this tubing,at least not for our purpose. Just use the smallest tube in the pack that will fit ,Then cut a piece a piece just long enough to cover the wound portion of the string at the ball. My old Marlen sounds clean to me again! Hope this helps, Then put sring on as normal.
Ron C.

Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 28 October 2005 07:20 AM     profile     

To Ron Sodos;

Your statement is the reason why you do not want to cut that tube any longer than the wound portion of that string.

Ron C.

Ronald Comtois
Member

From: Bourne, Massachusetts, USA

posted 28 October 2005 07:31 AM     profile     
One more thing! Using tubing will stop the gouging and pitting of those bridge rollers on top of those fingers.Have not tried this on wound strings, there has been no need.

Ron C.

Peter Feller
Member

From: Palisades, New York, USA

posted 28 October 2005 08:02 AM     profile     
Another way to make the wrapped ends less likely to be a problem is to to tin them. By this I mean: Get out the soldering iron, flux and solder. Apply a thin film of flux, heat the wrapped area, and touch it with the solder when hot. The solder will run into the area nicely and make the end one solid mass. It is definitely more labor than heat shrink, but I do a few sets at a time. The solder does not increase the diameter of the wrap, and can actually reduce string breakage somewhat. Good luck.
richard burton
Member

From: Britain

posted 28 October 2005 12:40 PM     profile     
Rick,
It's trial and error with the plastic.
Nylon is too soft, and mutes the string too much.
The type of plastic I use comes from Kodak film canisters.
R B
Thom Ferman
Member

From: Las Vegas, NV, USA

posted 28 October 2005 04:07 PM     profile     
Rick, I agree many would pass by this post but I (and my pocketbook) have benefited greatly by trying this.

I have a pre-BCT Carter D-10 that had some really nasty "sitaring" on strings 3-4-5. There are an extremely small amount of groove marks on the changer fingers but the string twinge kept me from ever getting a good tone, particularly higher up the neck. I had tried eq'ing it, hiding it with chorus/delay, changing bar pressure and screwing with my technique, all to no avail.

After reading Ronald's post, I had some small nylon insulating tubing and put enough on the ends of the troublesome strings to cover the windings. Miracle of miracles the string ring is GONE! I will still get this guitar back to Carter someday for a BCT conversion (which includes machining the changer fingers), but now don't feel compelled to do it right away! Thanks Ronald for a truly useful tip with amazingly positive results!

Miracles do happen - Thom

Jon Kostal
Member

From: Westmont, Illinois, USA

posted 30 October 2005 09:55 AM     profile     
Peter,
Thanks for your idea of tinning the wound ends of the plain strings-works great! I've been plagued with this problem for years, no matter what guitar! I was beginning to think it was something I was doing as a player. Years ago on my D10 emmons p/p I went so far as to buy a new e9 pickup, and then a complete new changer, neither worked. I'm happy now, better late than never!

------------------
Jon
Uncle Jons Music


Larry R
Member

From: Navasota, Tx.

posted 04 November 2005 04:03 PM     profile     
Geo. L's makes an .011 string with the ball end wrapped with nylon thread. I used a few of them but they got to muting out the tone so I stopped using them. The nylon wrapping would protrude past the finger which dampened the tone.
Fred Nolen
Member

From: Mohawk, Tennessee, USA

posted 04 November 2005 04:30 PM     profile     
Peter and Jon,

Do you use a torch or soldering iron to heat the ends after the flux is applied?

I had not noticed the problem until I got my new guitar. Now I hear it on my old one as well. I don't fully understand the mechanics of the problem but it appears to be somewhat universal. I absolutely love the tone of my new guitar and the idea of correcting the problem at the individual string level seems to be the way to go.

Thanks to all for your input.

Ol' Fred

Jon Kostal
Member

From: Westmont, Illinois, USA

posted 04 November 2005 05:32 PM     profile     
Fred, I use a 25 watt soldering iron and rosin core solder, the same stuff I use for soldering wires. Works great!

Good luck

------------------
Jon
Uncle Jons Music


All times are Pacific (US)

next newest topic | next oldest topic

Administrative Options: Close Topic | Archive/Move | Delete Topic
Post New Topic  
Hop to:

Contact Us | The Pedal Steel Pages

Note: Messages not explicitly copyrighted are in the Public Domain.

Powered by Infopop www.infopop.com © 2000
Ultimate Bulletin Board 5.46

Our mailing address is:
The Steel Guitar Forum
148 South Cloverdale Blvd.
Cloverdale, CA 95425 USA

Support the Forum