Steel Guitar Strings
Strings & instruction for lap steel, Hawaiian & pedal steel guitars
http://SteelGuitarShopper.com
Ray Price Shuffles
Classic country shuffle styles for Band-in-a-Box, by BIAB guru Jim Baron.
http://steelguitarmusic.com

This Forum is CLOSED.
Go to bb.steelguitarforum.com to read and post new messages.


  The Steel Guitar Forum
  Electronics
  Tube Amp On It's Side OK??

Post New Topic  
your profile | join | preferences | help | search

next newest topic | next oldest topic
Author Topic:   Tube Amp On It's Side OK??
Jon James
Member

From: Beverly Hills, California, USA

posted 24 July 2005 02:41 PM     profile     
Can anyone tell me if there is any damage that can be caused to a tube amplifier if I leave it permantly on it's side. I have just totally run out of room for my stuff, and the one little 6' of wall space that my wife has a lotted me in our family room for my music stuff is just too tight, so I figure I can save a lot of room by putting my 2x12 tube amp on it's side, and that way I can point it at me while I practice also. Any problems?
Thanks
Donny Hinson
Member

From: Balto., Md. U.S.A.

posted 24 July 2005 03:20 PM     profile     
Just make sure the power tubes are on the bottom side. That way, the heat they give off will have to travel farther to get to the wood cabinet.
Jon James
Member

From: Beverly Hills, California, USA

posted 24 July 2005 03:28 PM     profile     
Thanks Donny,
The tubes are in the middle of the amp , so I they are equidistant from either side. Any other issues? How about the reverb unit? Thanks
Dave Zirbel
Member

From: Sebastopol, CA USA

posted 24 July 2005 07:12 PM     profile     
A lot of times when I play with tube amps I set them on their side to disperse the heat generated by the tubes. The design flaw of Fender amps is that the tubes are under the chassis. That's why the components get cooked and dry up and need to be replaced more often.
Bob Leaman
unregistered
posted 24 July 2005 07:38 PM           
Almost all of the original tube manufacturers recommended operating tubes in a vertical position. The preferred vertical position is base down. Base up position causes the tube heat to influence any component above the tube. It is interesting to note that slightly more than 90% of the problems encountered with tube type equipment can be traced to tubes. All commercial and industrial applications have converted to solid state unless there is no solid state equivalent equipment available for a particular task.
David Doggett
Member

From: Philadelphia, Pennsylvania, USA

posted 24 July 2005 09:17 PM     profile     
I play through a Dual Showman Reverb head or a Super Twin Reverb head. To save space on small stages I routinely set them sideways on end. It seems to have no effect on the tube sound, and probably vents the tube heat better. As far as what Bob L. just said, in my experience there is no solid state amp equivalent to tube tone.
Ricky Littleton
Member

From: Steely-Eyed Missile Man from Orlando, Florida USA

posted 25 July 2005 05:37 AM     profile     
Just my $0.02 worth based on almost 30 years in electronic maintenance.

Tubes, stored or otherwise are best maintained in an vertical orientation. The reasons are plain and simple:

1.- elements (most notably the filament)are suspended within the tube envelope at one end. Therefore, tubes left on their side for extended periods may experience (due to variations in quality of manufacture)some "sag" internally and run the risk of premature failure due to this. Even if the elements do not sag enough to directly short, the distance between the elements (a critical parameter known as interelectrode capacitance) could change and may alter the overall performance of the tube.

2.- Filaments run red-hot when running. The plate (anode) may also run a little red if the gain is way up. This means HIGH surface temperatures. Remember, metallic pliability is obtained through heating. This being the case, it is easy to see if a tube is operated on its side, the risk of filament deformation through thermally induced sag is greater than if the tube is operated upright.

In military applications, ruggedized tubes (in metallic envelopes) were manufactured with more robust elements to offset the above problems, however, our modern audio tubes are manufactured nowhere near these ruggedized standards.

Just my thoughts on this, but as I said, it's info derived from a long-time career in electronics (radar and my own repair business).

Thanks for letting me rant...

Ricky...

------------------
Emmons LeGrande - 8x4
Session 400 Ltd, Nashville 112,Hilton Volume pedal, Peterson VS-II Tuner
Dan-Echo, E-Bow, Ibanez Distortion, Bo-Bro, Ibanez Auto-Wah, PX4 Pandoras Box

[This message was edited by Ricky Littleton on 25 July 2005 at 05:38 AM.]

Jody Carver
Member

From: The Knight Of Fender Tweed~ Dodger Blue Forever

posted 25 July 2005 06:28 AM     profile     
Keep ranting I'm learning something here.
ed packard
Member

From: Show Low AZ

posted 25 July 2005 07:23 AM     profile     
Keep the heat away from those electrolytic capacitors (big silver cylinder shaped things) as they are a major source of amp problems = hum etc. as they "deform", dry up, or otherwise deteriorate.

Filament sag can also cause hum problems. As has been pointed out, the tube design is optimized for upright operation.

Dave Zirbel
Member

From: Sebastopol, CA USA

posted 25 July 2005 07:47 AM     profile     
That makes sense to me about tubes being vertical. I guess I'll just run a small fan in the back of my amp, or set my amp upside down.

I learned something too!

DZ

Blake Hawkins
Member

From: Land O'Lakes, Florida

posted 25 July 2005 08:46 AM     profile     
In modern equipment, the only tubes with filaments are rectifiers like the 5Y3GT.

In the "RCA Tube Manual Technical Series RC 23" It is stated that vertical mounting is preferred but horizontal mounting is permissable if pins 2 and 8 are in a vertical plane for a 5Y3GT.

Of course, you don't usually find tube rectifiers any more. The Fender Twin's use solid state diodes.

The construction of all the other tubes in the amp is "heater-cathode" where the heating element is tightly packed into a sleeve which is the cathode.

The tube manual states for the 6L6-GC and for the 12AX7A that "the tube may be mounted in any position."

This is not to say that you wouldn't encounter any of the problems mentioned above including internal distortion of other tube elements.

However, the manufacturer was confident enough to reccomend mounting in any position for the heater-cathode tubes.

Blake

All times are Pacific (US)

next newest topic | next oldest topic

Administrative Options: Close Topic | Archive/Move | Delete Topic
Post New Topic  
Hop to:

Contact Us | The Pedal Steel Pages

Note: Messages not explicitly copyrighted are in the Public Domain.

Powered by Infopop www.infopop.com © 2000
Ultimate Bulletin Board 5.46

Our mailing address is:
The Steel Guitar Forum
148 South Cloverdale Blvd.
Cloverdale, CA 95425 USA

Support the Forum